English
Français
Curing UV lamp RL-014
The RL-014 UV curing lamp is a compact and powerful lamp designed for rapid curing of adhesives and photosensitive materials used in mobile phone repair and other technical applications. It is ideal for UV adhesives, photosensitive green oil, optical adhesives, shadow-free adhesives and resins requiring UV light to cure effectively.
2.200,00 DA
| Spécification | Détail |
|---|---|
| Marque | Relife |
| Modèle | RL-014 |
| Type | Lampe de polymérisation UV |
| Alimentation | USB (5 V — compatible PC, chargeur ou batterie externe) |
| Tension | 5 V DC |
| Puissance | 5 W |
| Courant | Environ 1400 mA |
| Longueur d’onde UV | ~395 nm (UV-A) |
| Modes d’éclairage | Plusieurs niveaux : forte lumière / faible lumière / flash |
| Dimensions | Compacte (env. 58 × 54 × 42 mm) |
| Poids net | ~100 g |
| Accessoires inclus | Câble USB |
| Refroidissement | Grille intégrée pour dissipation thermique |
⚡ Highlights
✅ Very fast curing—hardens photosensitive glues in seconds.
✅ Versatile USB Power Supply—works with computer, wall charger or external battery.
✅ Adjustable modes—several power levels depending on the material.
✅ Compact and portable design—easy to use even in tight workspaces.
✅ Sturdy construction—durable components and strong assembly.
✅ Built-in cooling—for extended lifespan.
📌 Main applications
✔ Repair of mobile phones — curing of UV adhesives and photosensitive green oil used for screens or components.
✔ General electronics—polymerization of optical adhesives, UV resins, technical inks and adhesives.
✔ Light industrial applications—rapid curing for small UV-requiring assemblies.
Related Products
- ESP32-WROVER is a powerful, generic WiFi-BT-BLE MCU module that targets a wide variety of applications,ranging from low-power sensor networks to the most demanding tasks, such as voice encoding, music streamingand MP3 decoding. The ESP32-WROVER has two versions: The ESP32-WROVER IPEX Module uses an IPEX antenna while the ESP32-WROVER PCB module has a PCB antenna.
4 Digit 0.56 inch 7 Segment 4 Bit Red LED Digital Display Module Tube with Clock Point for Arduino
The HW-201 IR infrared obstacle detection module can detect obstacles within a distance range of 2 cm to 30 cm, with a detection angle of 35 degrees.
It can operate with a supply voltage of 3.3 V to 5 V and has a maximum current consumption of 100 mA. The module outputs a digital signal, high when an obstacle is detected, low when no obstacle is detected.
The infrared LED has a wavelength of 940 nm and an operating frequency of 38 kHz. The module operates at temperatures between -25 °C and +55 °C.
The MQ3 analog gas sensor is suitable for detecting alcohol; this sensor can be used in a breathalyzer.
It has high sensitivity to alcohol and low sensitivity to gasoline.
The sensitivity can be adjusted using a potentiometer.
The Arduino UNO is the best board to get started with electronics and coding. If this is your first experience tinkering with the platform, the UNO is the most robust board you can start playing with. The UNO is the most used and documented board of the whole Arduino family.
3S 20A Li-ion 18650 BMS Lithium Battery Protection Board is a Battery Management System (BMS) designed for 3-cell 18650 Li-ion battery packs. It offers overcharge, over-discharge, short-circuit, and overcurrent protection to ensure the safe operation and longevity of your battery packs.
5621BS Red LED Display 2 Digit 7 Segment Common Anode Digital Display 18 Pin 0.56 inch
The MQ2 analog gas sensor is used in gas leak detection equipment. This sensor is suitable for detecting LPG, butane, propane, methane, alcohol, hydrogen, and smoke. It has high sensitivity and a fast response time; the sensitivity can be adjusted using a potentiometer.
5mm 5537 LDR is a 5mm light-dependent resistor with a “5537” model number, which is a photosensitive component that changes its electrical resistance based on the intensity of ambient light. Its resistance is high in darkness and decreases as light increases, making it useful for light-sensitive applications like automatic lighting systems, alarms, and light-level detection.
Transceiver module based on an NRF24L01 allowing a 2.4 GHz wireless connection. This module communicates with an Arduino or compatible microcontroller via the SPI bus.
