English
Français
Arduino Starter Kit
The Arduino Starter Kit is a comprehensive, beginner-friendly bundle designed to teach the fundamentals of electronics, coding, and prototyping through hands-on projects. It typically includes an Arduino Uno board, jumper wires, a breadboard, and various sensors/actuators (LEDs, motors, sensors…)….
9.200,00 DA
The ARDUINO Starter kit contains:
- x 1 Arduino UNO R3 board (compatible)
- x 1 Breadboard 830 points
- x 1 LCD Module 1602
- x 1 Keyboard 4*4
- x 1 Display 7 Segment 1 Digit
- x 1 Display 7 Segment 4 Digit
- x 1 Dot matrix 8*8
- x 1 74HC595N
- x 1 Temperature sensor LM35
- x 2 DS18B20 Buzzer
- x 1 Servo SG-90
- x 1 Stepper motor 5V
- x 1 ULN2003 driver card
- x 1 DS1302 Clock Module
- x 1 Joystick Module
- x 1 Channel Relay module
- x 1 pack wire connector M-M 65 pcs
- x 1 Temperature and humidity sensor module DHT11
- x 1 fich stack 9v with door
- x 1 Càble USB
- x 1 Infrared remote control with receiver
- x 1 Sound detection sensor
- x 1 Potentiometer 10K
- 1 x 5mm flame sensor
- 1 x LDR 5mm
- x 10 LED 5mm red
- x 10 5mm yellow LED
- x 10 LED 5mm green
- 10 x 220R resistance 1/4W
- 10 x 1k resistance 1/4W
- 10 x 10K resistance 1/4W
- x 5 Push button 12×12 mm
- x 2 ball switch
Related Products
The HW-201 IR infrared obstacle detection module can detect obstacles within a distance range of 2 cm to 30 cm, with a detection angle of 35 degrees.
It can operate with a supply voltage of 3.3 V to 5 V and has a maximum current consumption of 100 mA. The module outputs a digital signal, high when an obstacle is detected, low when no obstacle is detected.
The infrared LED has a wavelength of 940 nm and an operating frequency of 38 kHz. The module operates at temperatures between -25 °C and +55 °C.
The MQ2 analog gas sensor is used in gas leak detection equipment. This sensor is suitable for detecting LPG, butane, propane, methane, alcohol, hydrogen, and smoke. It has high sensitivity and a fast response time; the sensitivity can be adjusted using a potentiometer.
4 Digit 0.56 inch 7 Segment 4 Bit Red LED Digital Display Module Tube with Clock Point for Arduino
The SG90 servo motor is a type of continuous rotation motor controlled by a digital signal. It is used in projects such as robotics, position control systems, and DIY projects.
The Arduino UNO is the best board to get started with electronics and coding. If this is your first experience tinkering with the platform, the UNO is the most robust board you can start playing with. The UNO is the most used and documented board of the whole Arduino family.
- ESP32-WROVER is a powerful, generic WiFi-BT-BLE MCU module that targets a wide variety of applications,ranging from low-power sensor networks to the most demanding tasks, such as voice encoding, music streamingand MP3 decoding. The ESP32-WROVER has two versions: The ESP32-WROVER IPEX Module uses an IPEX antenna while the ESP32-WROVER PCB module has a PCB antenna.
0.56 inch Red 4 Digit 7 Segment LED Display CC 12pin
The “LJ12A3-4-Z/BX” is an inductive proximity sensor that detects metal objects within a 4mm range. It operates on a DC 6-36V power supply and has an NPN (Normally Open) digital output, meaning it completes a circuit to the signal line when it detects metal. These sensors are used in industrial automation for non-contact switching, control, and detection
3S 20A Li-ion 18650 BMS Lithium Battery Protection Board is a Battery Management System (BMS) designed for 3-cell 18650 Li-ion battery packs. It offers overcharge, over-discharge, short-circuit, and overcurrent protection to ensure the safe operation and longevity of your battery packs.
Arduino Nano has enough processing power to control many electronic components. It has several I/O pins, which allows to connect it to many components. , it is a compact and reduced version of Arduino uno maroc.
Arduino Nano has 14 digital inputs/types (6 of which can be used as PWM outputs), 8 analog inputs.
Stepper motor 28BY J-48 with Driver ULN2003
the ULN2003 stepper motor driver or in English stepper motor, unipolar (4 phases/ 5 wires ) allows you to easily plug the small motor 28BY J-48 5v gràce to the 5 pin male connector and connects easily to an arduino or other through a 4 pin connector for control signals and Gnd (ground/-). The power supply of ULN2003 is between 5 and 12V.
