English
Français
Arduino Mega 2560 R3 With Cable
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button.
4.200,00 DA
Universal Atmega2560 microcontroller module for use in prototypes and projects with microcontrollers. Compatible with the Arduino® Mega 2560 design.
It is a clone that was built according to the original scheme.
The programming is done using the USB UART CH340 converter.
You will need a USB A / B cable to communicate with the board .
Parameters:
- Supply voltage: 5V (USB), 7-12V (power adapter)
- I / O pin voltage: 5V
- Arduino® Mega 2560 R3 bootloader installed
- USB-UART chip: CH340
- Microcontroller: ATmega2560
- Maximum clock frequency: 16 MHz
- SRAM memory: 8 kB
- Flash memory: 256 KB (8 KB is reserved for bootloader)
- EEPROM memory: 4 kB
- I / O Ports: 54
- PWM outputs: 15
- Number of analog inputs: 16 (channels of A / C converter)
- Serial interfaces: UART, SPI, I2C
- External interrupts
- Dimensions: 101 x 54 x 15 mm
- Goldpins soldered into the board
| Weight | 1 kg |
|---|---|
| Brand | Arduino |
Related Products
The MQ3 analog gas sensor is suitable for detecting alcohol; this sensor can be used in a breathalyzer.
It has high sensitivity to alcohol and low sensitivity to gasoline.
The sensitivity can be adjusted using a potentiometer.
A 5v relay is an automatic switch that is commonly used in an automatic control circuit and to control a high-current using a low-current signal. The input voltage of the relay signal ranges from 0 to 5V.
Transceiver module based on an NRF24L01 allowing a 2.4 GHz wireless connection. This module communicates with an Arduino or compatible microcontroller via the SPI bus.
The SHT3x sensor is the most accurate and precise sensor for measuring humidity and temperature parameters compared to other temperature sensors like LM35, Thermistor, DS18B20 & DHT11/DHT22. Thus SHT3x can be used for industrial applications because of the high accuracy and good sensitivity. Its Relative Humidity operating range is 0 – 100% and Temperature operating range is -40° to +125°C (-40° to +257°F).
Seven-segment display (5611AH):
- The 7-segment displays consist of a series of LEDs placed to form numbers.
- A 7-segment display allows you to view the digits from 0 to 9.
- Typical voltage: 2.2v / Current per segment max: 30mA
5621BS Red LED Display 2 Digit 7 Segment Common Anode Digital Display 18 Pin 0.56 inch
3S 20A Li-ion 18650 BMS Lithium Battery Protection Board is a Battery Management System (BMS) designed for 3-cell 18650 Li-ion battery packs. It offers overcharge, over-discharge, short-circuit, and overcurrent protection to ensure the safe operation and longevity of your battery packs.
MODULE compatible Arduino to control 4 motors DC or 2 stepper motors and have 2 connections for servomotors. This shield uses pins D3 to D12 for operation (direction, speed, etc).
The module is based on two L293D drivers and can control up to 4 DC motors with an intensity of 0.6 A per output (1.2 A at peak).
0.56 inch Red 4 Digit 7 Segment LED Display CC 12pin
The HW-201 IR infrared obstacle detection module can detect obstacles within a distance range of 2 cm to 30 cm, with a detection angle of 35 degrees.
It can operate with a supply voltage of 3.3 V to 5 V and has a maximum current consumption of 100 mA. The module outputs a digital signal, high when an obstacle is detected, low when no obstacle is detected.
The infrared LED has a wavelength of 940 nm and an operating frequency of 38 kHz. The module operates at temperatures between -25 °C and +55 °C.
