English
Français
0.56 inch 4 Digit 7 Segment LED Display CA Red
4 Digit 0.56 inch 7 Segment 4 Bit Red LED Digital Display Module Tube with Clock Point for Arduino
Description
- The module is based on a 4 (0.56 inch) digital tube which can display the clock point. The decimal point is not displayed and the driver chip is TM1637.
- Simply two signal lines can do 4 digit 7 segment LED MCU control. It can be used to display the integer, clock, stopwatch, score, etc.
Features
1.Compatible for Arduino UNO R3/MEGA2560/Leonardo.
2.4-digit alpha-numeric red display with clock dot.
3. 8 gray adjustable.
4. Power supply should be 3.3~5.5V DC.
5. Interface logic level can be 3.3V/5V.
6. 4 screw mounting holes which diameter is 2.2mm.
Related Products
The ESP32-CAM is an ESP-WROOM-32 development board from AI Thinker, paired with a 2MP OV2640 color camera. The ESP32-CAM module also features an SD card reader that can be used to record images when an event is detected (e.g., presence or motion detector).
5mm 5537 LDR is a 5mm light-dependent resistor with a “5537” model number, which is a photosensitive component that changes its electrical resistance based on the intensity of ambient light. Its resistance is high in darkness and decreases as light increases, making it useful for light-sensitive applications like automatic lighting systems, alarms, and light-level detection.
Seven-segment display (5611AH):
- The 7-segment displays consist of a series of LEDs placed to form numbers.
- A 7-segment display allows you to view the digits from 0 to 9.
- Typical voltage: 2.2v / Current per segment max: 30mA
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button.
High-capacity brushless motor, maximizes equipment power and extends service life and reduces the risk of breakdowns. This motor is commonly used in industrial applications, comfortable and quite simple in its use, as well as its energy consumption is low.
3S 20A Li-ion 18650 BMS Lithium Battery Protection Board is a Battery Management System (BMS) designed for 3-cell 18650 Li-ion battery packs. It offers overcharge, over-discharge, short-circuit, and overcurrent protection to ensure the safe operation and longevity of your battery packs.
A 5v relay is an automatic switch that is commonly used in an automatic control circuit and to control a high-current using a low-current signal. The input voltage of the relay signal ranges from 0 to 5V.
The MQ3 analog gas sensor is suitable for detecting alcohol; this sensor can be used in a breathalyzer.
It has high sensitivity to alcohol and low sensitivity to gasoline.
The sensitivity can be adjusted using a potentiometer.
Stepper motor 28BY J-48 with Driver ULN2003
the ULN2003 stepper motor driver or in English stepper motor, unipolar (4 phases/ 5 wires ) allows you to easily plug the small motor 28BY J-48 5v gràce to the 5 pin male connector and connects easily to an arduino or other through a 4 pin connector for control signals and Gnd (ground/-). The power supply of ULN2003 is between 5 and 12V.
The HW-201 IR infrared obstacle detection module can detect obstacles within a distance range of 2 cm to 30 cm, with a detection angle of 35 degrees.
It can operate with a supply voltage of 3.3 V to 5 V and has a maximum current consumption of 100 mA. The module outputs a digital signal, high when an obstacle is detected, low when no obstacle is detected.
The infrared LED has a wavelength of 940 nm and an operating frequency of 38 kHz. The module operates at temperatures between -25 °C and +55 °C.
Transceiver module based on an NRF24L01 allowing a 2.4 GHz wireless connection. This module communicates with an Arduino or compatible microcontroller via the SPI bus.
