Français
English
- Neptune 4 Plus a été retiré de votre panier car il ne peut plus être acheté. Veuillez nous contacter si vous avez besoin d’aide.
- Ender-3 V3 KE a été retiré de votre panier car il ne peut plus être acheté. Veuillez nous contacter si vous avez besoin d’aide.
L298N Stepper Motor Driver Module
L298N is a high-power bipolar motor controller that can be used to control the speed and direction of two direct current (DC) motors
950,00 DA
Specifications
- H double-bridge of dc motor driver chip
- Chip: L298N (ST NEW)
- Logic voltage: 5V
- Driving voltage: 5V-35V
- logic current: 0 mA-36mA
- Drive current: 2A (MAX only bridge)
- Maximum power: 25W
- allowable temperature range. -20 ° C to 135 ° C
- Size: approx. 43 x 43 x 27mm
-L298N as main driver chip makes strong driving ability / small heating/ strong / low calorific value anti interference.
– The output pins have connections with clamps and OUT1, OUT2 of the first motor and OUT3, OUT4 marked for the second motor.
– Ensure sufficient voltage and current for your motor at the VCC and GND pins.
– Built-78M05, power receiving of drive power, but when the drive power exceeds 12V, please use the power of 5V external power supply.
Produits connexes
3S 20A Li-ion 18650 BMS Lithium Battery Protection Board is a Battery Management System (BMS) designed for 3-cell 18650 Li-ion battery packs. It offers overcharge, over-discharge, short-circuit, and overcurrent protection to ensure the safe operation and longevity of your battery packs.
0.56 inch Red 4 Digit 7 Segment LED Display CC 12pin
The SHT3x sensor is the most accurate and precise sensor for measuring humidity and temperature parameters compared to other temperature sensors like LM35, Thermistor, DS18B20 & DHT11/DHT22. Thus SHT3x can be used for industrial applications because of the high accuracy and good sensitivity. Its Relative Humidity operating range is 0 – 100% and Temperature operating range is -40° to +125°C (-40° to +257°F).
12mm 12528 LDR is a type of photoresistor with a 12mm diameter and the model number GL12528, which changes its resistance based on the intensity of light it is exposed to. The resistance of the component is high in the dark and drops significantly as light increases, making it useful for detecting ambient light levels
Stepper motor 28BY J-48 with Driver ULN2003
the ULN2003 stepper motor driver or in English stepper motor, unipolar (4 phases/ 5 wires ) allows you to easily plug the small motor 28BY J-48 5v gràce to the 5 pin male connector and connects easily to an arduino or other through a 4 pin connector for control signals and Gnd (ground/-). The power supply of ULN2003 is between 5 and 12V.
The MQ2 analog gas sensor is used in gas leak detection equipment. This sensor is suitable for detecting LPG, butane, propane, methane, alcohol, hydrogen, and smoke. It has high sensitivity and a fast response time; the sensitivity can be adjusted using a potentiometer.
MODULE compatible Arduino to control 4 motors DC or 2 stepper motors and have 2 connections for servomotors. This shield uses pins D3 to D12 for operation (direction, speed, etc).
The module is based on two L293D drivers and can control up to 4 DC motors with an intensity of 0.6 A per output (1.2 A at peak).
The HW-201 IR infrared obstacle detection module can detect obstacles within a distance range of 2 cm to 30 cm, with a detection angle of 35 degrees.
It can operate with a supply voltage of 3.3 V to 5 V and has a maximum current consumption of 100 mA. The module outputs a digital signal, high when an obstacle is detected, low when no obstacle is detected.
The infrared LED has a wavelength of 940 nm and an operating frequency of 38 kHz. The module operates at temperatures between -25 °C and +55 °C.
0.56 inch 4 Digit 7 Segment LED Display Red Clock 12 Pin Common Cathode Digital Display
The MQ3 analog gas sensor is suitable for detecting alcohol; this sensor can be used in a breathalyzer.
It has high sensitivity to alcohol and low sensitivity to gasoline.
The sensitivity can be adjusted using a potentiometer.
5mm 5537 LDR is a 5mm light-dependent resistor with a « 5537 » model number, which is a photosensitive component that changes its electrical resistance based on the intensity of ambient light. Its resistance is high in darkness and decreases as light increases, making it useful for light-sensitive applications like automatic lighting systems, alarms, and light-level detection.
