Français
English
Arduino Mega 2560 R3 With Cable
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button.
4.200,00 DA
Universal Atmega2560 microcontroller module for use in prototypes and projects with microcontrollers. Compatible with the Arduino® Mega 2560 design.
It is a clone that was built according to the original scheme.
The programming is done using the USB UART CH340 converter.
You will need a USB A / B cable to communicate with the board .
Parameters:
- Supply voltage: 5V (USB), 7-12V (power adapter)
- I / O pin voltage: 5V
- Arduino® Mega 2560 R3 bootloader installed
- USB-UART chip: CH340
- Microcontroller: ATmega2560
- Maximum clock frequency: 16 MHz
- SRAM memory: 8 kB
- Flash memory: 256 KB (8 KB is reserved for bootloader)
- EEPROM memory: 4 kB
- I / O Ports: 54
- PWM outputs: 15
- Number of analog inputs: 16 (channels of A / C converter)
- Serial interfaces: UART, SPI, I2C
- External interrupts
- Dimensions: 101 x 54 x 15 mm
- Goldpins soldered into the board
| Poids | 1 kg |
|---|---|
| Marque | Arduino |
Produits connexes
The « LJ12A3-4-Z/BX » is an inductive proximity sensor that detects metal objects within a 4mm range. It operates on a DC 6-36V power supply and has an NPN (Normally Open) digital output, meaning it completes a circuit to the signal line when it detects metal. These sensors are used in industrial automation for non-contact switching, control, and detection
This is a general OLED display Module, 0.91inch diagonal, 128×32 pixels, with embedded controller, communicating via I2C interface.
The SG90 servo motor is a type of continuous rotation motor controlled by a digital signal. It is used in projects such as robotics, position control systems, and DIY projects.
5621BS Red LED Display 2 Digit 7 Segment Common Anode Digital Display 18 Pin 0.56 inch
5mm 5537 LDR is a 5mm light-dependent resistor with a « 5537 » model number, which is a photosensitive component that changes its electrical resistance based on the intensity of ambient light. Its resistance is high in darkness and decreases as light increases, making it useful for light-sensitive applications like automatic lighting systems, alarms, and light-level detection.
Stepper motor 28BY J-48 with Driver ULN2003
the ULN2003 stepper motor driver or in English stepper motor, unipolar (4 phases/ 5 wires ) allows you to easily plug the small motor 28BY J-48 5v gràce to the 5 pin male connector and connects easily to an arduino or other through a 4 pin connector for control signals and Gnd (ground/-). The power supply of ULN2003 is between 5 and 12V.
Transceiver module based on an NRF24L01 allowing a 2.4 GHz wireless connection. This module communicates with an Arduino or compatible microcontroller via the SPI bus.
0.56 inch Red 4 Digit 7 Segment LED Display CC 12pin
This is 125K RFID Tag. The RFID technology is used for sensing and identifying tagged people and objects for access control, automation, and a whole range of different applications.
Operating on a frequency of 125kHz, these tokens are all pre-programmed with unique ID numbers to communicate wirelessly with RFID Readers over distances of around 10cm or less. This means you can attach it to vehicles or items, keyrings or even pets’ collars to keep track of the location via an array of readers in the office, warehouse or home.
