Français
English
SHT3x Humidity & Temperature Sensor
The SHT3x sensor is the most accurate and precise sensor for measuring humidity and temperature parameters compared to other temperature sensors like LM35, Thermistor, DS18B20 & DHT11/DHT22. Thus SHT3x can be used for industrial applications because of the high accuracy and good sensitivity. Its Relative Humidity operating range is 0 – 100% and Temperature operating range is -40° to +125°C (-40° to +257°F).
950,00 DA
SHT3X Temperature and Humidity sensor, How it works and its pinout diagram:
There are many sensor boards out in the market which can measure temperature and humidity wisely, but when you need an accurate, precise and compact only few of them comes under the list. One of them is SHT3x series sensor as they are successors of SHT2x that set the industry level standards in humidity and temperature measurements, SHT3x comes with SHT30 and base version, SHT31 a standard version and All the way goes to SHT35 High end version which can be used in automotive level sensing.
SHT3x is packed with a completely new CMO Sens Chip, which will increase reliability along with improved accuracy in measuring. The SHT3x offers a range of new features when compared with SHT2x and other sensors, such as enhanced signal processing, two distinctive and user-selectable I2C addresses(0x44 or 0x45), an alert mode with programmable humidity and temperature limits, and communication speeds of up to 1 MHz.
Related Project: Digital Thermometer using LM35 and Arduino
SHT3x is more precise and accurate than other sensors like LM35, DHT11, DHT22, Thermistors, DS18B20 and has a greater range of measuring temperature than few of them which is -40° to +125°C (-40° to +257°F) and relative humidity ranging from 0 to 100%. It also has wide input voltage range from 2.2v to 5.5v.
It has an accuracy of ±3% to ±1.5% in measuring humidity from base version to high-end version respectively, And ±0.3 to ±0.1 in temperature measurements.
Specifications:
| Output | I²C, Voltage Out |
| Supply voltage range | 2.15 to 5.5 V |
| Energy consumption | 4.8µW (at 2.4 V, low repeatability, 1 measurement / s) |
| RH operating range | 0 – 100% RH |
| T operating range | -40 to +125°C (-40 to +257°F) |
| RH response time | 8 sec (tau63%) |
SHT3x Pinout diagram:
Below is the pinout diagram of SHT3X Temperature and Humidity Sensor.
From the above pinout diagram, There you can see 4 pins two pins for Voltage input and Ground and another two pins for I2C connection SCL and SDA.
Required Components:
- Sensirion SHT31 Humidity Temperature Sensor
- Arduino UNO R3 Development Board
- JHD162A 16×2 LCD Display
- Few connecting wires
Circuit Diagram:
Connect all the required components as shown in the above schematic diagram. Here we used LCD module with I2C adapter if you wish to connect it directly with out I2C refer the below link.
Connect Arduino with LCD Display with out I2C.
After connecting everything upload the code to Arduino, so it works accordingly.
Source Code:
Copy the below code and paste it in Arduino IDE, and select the correct board and serial port and click upload.
You need 2 libraries to run the below code you can directly install them through library manager or download them through below links manually.
| Marque | Arduino |
|---|
Produits connexes
3S 20A Li-ion 18650 BMS Lithium Battery Protection Board is a Battery Management System (BMS) designed for 3-cell 18650 Li-ion battery packs. It offers overcharge, over-discharge, short-circuit, and overcurrent protection to ensure the safe operation and longevity of your battery packs.
This is 125K RFID Tag. The RFID technology is used for sensing and identifying tagged people and objects for access control, automation, and a whole range of different applications.
Operating on a frequency of 125kHz, these tokens are all pre-programmed with unique ID numbers to communicate wirelessly with RFID Readers over distances of around 10cm or less. This means you can attach it to vehicles or items, keyrings or even pets’ collars to keep track of the location via an array of readers in the office, warehouse or home.
5621BS Red LED Display 2 Digit 7 Segment Common Anode Digital Display 18 Pin 0.56 inch
The HW-201 IR infrared obstacle detection module can detect obstacles within a distance range of 2 cm to 30 cm, with a detection angle of 35 degrees.
It can operate with a supply voltage of 3.3 V to 5 V and has a maximum current consumption of 100 mA. The module outputs a digital signal, high when an obstacle is detected, low when no obstacle is detected.
The infrared LED has a wavelength of 940 nm and an operating frequency of 38 kHz. The module operates at temperatures between -25 °C and +55 °C.
0.56 inch Red 4 Digit 7 Segment LED Display CC 12pin
4 Digit 0.56 inch 7 Segment 4 Bit Red LED Digital Display Module Tube with Clock Point for Arduino
MODULE compatible Arduino to control 4 motors DC or 2 stepper motors and have 2 connections for servomotors. This shield uses pins D3 to D12 for operation (direction, speed, etc).
The module is based on two L293D drivers and can control up to 4 DC motors with an intensity of 0.6 A per output (1.2 A at peak).
Seven-segment display (5611AH):
- The 7-segment displays consist of a series of LEDs placed to form numbers.
- A 7-segment display allows you to view the digits from 0 to 9.
- Typical voltage: 2.2v / Current per segment max: 30mA
Transceiver module based on an NRF24L01 allowing a 2.4 GHz wireless connection. This module communicates with an Arduino or compatible microcontroller via the SPI bus.
Stepper motor 28BY J-48 with Driver ULN2003
the ULN2003 stepper motor driver or in English stepper motor, unipolar (4 phases/ 5 wires ) allows you to easily plug the small motor 28BY J-48 5v gràce to the 5 pin male connector and connects easily to an arduino or other through a 4 pin connector for control signals and Gnd (ground/-). The power supply of ULN2003 is between 5 and 12V.
A 5v relay is an automatic switch that is commonly used in an automatic control circuit and to control a high-current using a low-current signal. The input voltage of the relay signal ranges from 0 to 5V.
