Français
English
L298N Stepper Motor Driver Module
L298N is a high-power bipolar motor controller that can be used to control the speed and direction of two direct current (DC) motors
950,00 DA
Specifications
- H double-bridge of dc motor driver chip
- Chip: L298N (ST NEW)
- Logic voltage: 5V
- Driving voltage: 5V-35V
- logic current: 0 mA-36mA
- Drive current: 2A (MAX only bridge)
- Maximum power: 25W
- allowable temperature range. -20 ° C to 135 ° C
- Size: approx. 43 x 43 x 27mm
-L298N as main driver chip makes strong driving ability / small heating/ strong / low calorific value anti interference.
– The output pins have connections with clamps and OUT1, OUT2 of the first motor and OUT3, OUT4 marked for the second motor.
– Ensure sufficient voltage and current for your motor at the VCC and GND pins.
– Built-78M05, power receiving of drive power, but when the drive power exceeds 12V, please use the power of 5V external power supply.
Produits connexes
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button.
A 5v relay is an automatic switch that is commonly used in an automatic control circuit and to control a high-current using a low-current signal. The input voltage of the relay signal ranges from 0 to 5V.
Ardess Digital Mini Thermometer with cable allows you to easily and fast know the environment temperature around you anywhere
The thermometer comes with 1m cable metal sensor probe, perfect for use in refrigerator, aquarium tank, fish tank,pet cage, kitchens,3D printer, solar system, cellar,humidors, incubator or any other places that require monitoring of temperature.
The « LJ12A3-4-Z/BX » is an inductive proximity sensor that detects metal objects within a 4mm range. It operates on a DC 6-36V power supply and has an NPN (Normally Open) digital output, meaning it completes a circuit to the signal line when it detects metal. These sensors are used in industrial automation for non-contact switching, control, and detection
3S 20A Li-ion 18650 BMS Lithium Battery Protection Board is a Battery Management System (BMS) designed for 3-cell 18650 Li-ion battery packs. It offers overcharge, over-discharge, short-circuit, and overcurrent protection to ensure the safe operation and longevity of your battery packs.
Seven-segment display (5611AH):
- The 7-segment displays consist of a series of LEDs placed to form numbers.
- A 7-segment display allows you to view the digits from 0 to 9.
- Typical voltage: 2.2v / Current per segment max: 30mA
The HW-201 IR infrared obstacle detection module can detect obstacles within a distance range of 2 cm to 30 cm, with a detection angle of 35 degrees.
It can operate with a supply voltage of 3.3 V to 5 V and has a maximum current consumption of 100 mA. The module outputs a digital signal, high when an obstacle is detected, low when no obstacle is detected.
The infrared LED has a wavelength of 940 nm and an operating frequency of 38 kHz. The module operates at temperatures between -25 °C and +55 °C.
The MQ2 analog gas sensor is used in gas leak detection equipment. This sensor is suitable for detecting LPG, butane, propane, methane, alcohol, hydrogen, and smoke. It has high sensitivity and a fast response time; the sensitivity can be adjusted using a potentiometer.
Arduino Nano has enough processing power to control many electronic components. It has several I/O pins, which allows to connect it to many components. , it is a compact and reduced version of Arduino uno maroc.
Arduino Nano has 14 digital inputs/types (6 of which can be used as PWM outputs), 8 analog inputs.
4 Digit 0.56 inch 7 Segment 4 Bit Red LED Digital Display Module Tube with Clock Point for Arduino
MODULE compatible Arduino to control 4 motors DC or 2 stepper motors and have 2 connections for servomotors. This shield uses pins D3 to D12 for operation (direction, speed, etc).
The module is based on two L293D drivers and can control up to 4 DC motors with an intensity of 0.6 A per output (1.2 A at peak).
