Français
English
Arduino Mega 2560 R3 With Cable
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button.
4.200,00 DA
Universal Atmega2560 microcontroller module for use in prototypes and projects with microcontrollers. Compatible with the Arduino® Mega 2560 design.
It is a clone that was built according to the original scheme.
The programming is done using the USB UART CH340 converter.
You will need a USB A / B cable to communicate with the board .
Parameters:
- Supply voltage: 5V (USB), 7-12V (power adapter)
- I / O pin voltage: 5V
- Arduino® Mega 2560 R3 bootloader installed
- USB-UART chip: CH340
- Microcontroller: ATmega2560
- Maximum clock frequency: 16 MHz
- SRAM memory: 8 kB
- Flash memory: 256 KB (8 KB is reserved for bootloader)
- EEPROM memory: 4 kB
- I / O Ports: 54
- PWM outputs: 15
- Number of analog inputs: 16 (channels of A / C converter)
- Serial interfaces: UART, SPI, I2C
- External interrupts
- Dimensions: 101 x 54 x 15 mm
- Goldpins soldered into the board
| Poids | 1 kg |
|---|---|
| Marque | Arduino |
Produits connexes
3S 20A Li-ion 18650 BMS Lithium Battery Protection Board is a Battery Management System (BMS) designed for 3-cell 18650 Li-ion battery packs. It offers overcharge, over-discharge, short-circuit, and overcurrent protection to ensure the safe operation and longevity of your battery packs.
4 Digit 0.56 inch 7 Segment 4 Bit Red LED Digital Display Module Tube with Clock Point for Arduino
5mm 5537 LDR is a 5mm light-dependent resistor with a « 5537 » model number, which is a photosensitive component that changes its electrical resistance based on the intensity of ambient light. Its resistance is high in darkness and decreases as light increases, making it useful for light-sensitive applications like automatic lighting systems, alarms, and light-level detection.
A 5v relay is an automatic switch that is commonly used in an automatic control circuit and to control a high-current using a low-current signal. The input voltage of the relay signal ranges from 0 to 5V.
12mm 12528 LDR is a type of photoresistor with a 12mm diameter and the model number GL12528, which changes its resistance based on the intensity of light it is exposed to. The resistance of the component is high in the dark and drops significantly as light increases, making it useful for detecting ambient light levels
The « LJ12A3-4-Z/BX » is an inductive proximity sensor that detects metal objects within a 4mm range. It operates on a DC 6-36V power supply and has an NPN (Normally Open) digital output, meaning it completes a circuit to the signal line when it detects metal. These sensors are used in industrial automation for non-contact switching, control, and detection
5621BS Red LED Display 2 Digit 7 Segment Common Anode Digital Display 18 Pin 0.56 inch
The Arduino UNO is the best board to get started with electronics and coding. If this is your first experience tinkering with the platform, the UNO is the most robust board you can start playing with. The UNO is the most used and documented board of the whole Arduino family.
MODULE compatible Arduino to control 4 motors DC or 2 stepper motors and have 2 connections for servomotors. This shield uses pins D3 to D12 for operation (direction, speed, etc).
The module is based on two L293D drivers and can control up to 4 DC motors with an intensity of 0.6 A per output (1.2 A at peak).
Transceiver module based on an NRF24L01 allowing a 2.4 GHz wireless connection. This module communicates with an Arduino or compatible microcontroller via the SPI bus.
