English
Français
TL-Smoother – Filtering Module for Stepper Motor Drivers of 3D Printers
The TL-Smoother is a module that can be added to stepper motor drivers (A4988, DRV8825, etc.) that are utilized in 3D printers and CNC.
Its role is to reduce vibrations, ripples and mechanical noise generated by stepper motors, smoothing the electrical signal transmitted to the motor coils.
This module improves print quality, reduces ghosting/moiré phenomena on printed parts and extends the mechanical life of motors.
950,00 DA
⚙️ Technical Specifications
🔌 Compatibility: works with most 3D and CNC printer motherboards.
⚡ Supported drivers: A4988, DRV8825, TMC2100, and other similar drivers.
📐 Compact size easy to install between driver and engine.
🔄 Reduction of vibrations through diode filtering.
🛠️ Simple installation: plug & play with standard connectors.
📊 Optimal effect on engines at low speeds or subject to torque variations.
✅ Benefits
- Improves the fluidity of axis movements.
- Reduces mechanical noise from engines.
- Decreases the ghosting phenomenon on 3D prints.
- Extends the life of engines and belts.
- Easy to install and compatible with most 3D printers.
🛠️ Applications
- 3D printers (Prusa, Creality, Anet, Anycubic, etc.).
- Engraving or cutting CNC using stepper motors.
- DIY projects requiring stepper motor stabilization.
Related Products
This is a general OLED display Module, 0.91inch diagonal, 128×32 pixels, with embedded controller, communicating via I2C interface.
The SG90 servo motor is a type of continuous rotation motor controlled by a digital signal. It is used in projects such as robotics, position control systems, and DIY projects.
- ESP32-WROVER is a powerful, generic WiFi-BT-BLE MCU module that targets a wide variety of applications,ranging from low-power sensor networks to the most demanding tasks, such as voice encoding, music streamingand MP3 decoding. The ESP32-WROVER has two versions: The ESP32-WROVER IPEX Module uses an IPEX antenna while the ESP32-WROVER PCB module has a PCB antenna.
V-Slot is a high quality linear rail profile made of aluminium with an extremely smooth V-groove on the 4 sides. It is accurate, easy to work with and allows you unlimited design control by its modular nature.
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button.
Arduino Nano has enough processing power to control many electronic components. It has several I/O pins, which allows to connect it to many components. , it is a compact and reduced version of Arduino uno maroc.
Arduino Nano has 14 digital inputs/types (6 of which can be used as PWM outputs), 8 analog inputs.
Stepper motor 28BY J-48 with Driver ULN2003
the ULN2003 stepper motor driver or in English stepper motor, unipolar (4 phases/ 5 wires ) allows you to easily plug the small motor 28BY J-48 5v gràce to the 5 pin male connector and connects easily to an arduino or other through a 4 pin connector for control signals and Gnd (ground/-). The power supply of ULN2003 is between 5 and 12V.
3S 20A Li-ion 18650 BMS Lithium Battery Protection Board is a Battery Management System (BMS) designed for 3-cell 18650 Li-ion battery packs. It offers overcharge, over-discharge, short-circuit, and overcurrent protection to ensure the safe operation and longevity of your battery packs.
The HW-201 IR infrared obstacle detection module can detect obstacles within a distance range of 2 cm to 30 cm, with a detection angle of 35 degrees.
It can operate with a supply voltage of 3.3 V to 5 V and has a maximum current consumption of 100 mA. The module outputs a digital signal, high when an obstacle is detected, low when no obstacle is detected.
The infrared LED has a wavelength of 940 nm and an operating frequency of 38 kHz. The module operates at temperatures between -25 °C and +55 °C.
