English
Français
SHT3x Humidity & Temperature Sensor
The SHT3x sensor is the most accurate and precise sensor for measuring humidity and temperature parameters compared to other temperature sensors like LM35, Thermistor, DS18B20 & DHT11/DHT22. Thus SHT3x can be used for industrial applications because of the high accuracy and good sensitivity. Its Relative Humidity operating range is 0 – 100% and Temperature operating range is -40° to +125°C (-40° to +257°F).
950,00 DA
SHT3X Temperature and Humidity sensor, How it works and its pinout diagram:
There are many sensor boards out in the market which can measure temperature and humidity wisely, but when you need an accurate, precise and compact only few of them comes under the list. One of them is SHT3x series sensor as they are successors of SHT2x that set the industry level standards in humidity and temperature measurements, SHT3x comes with SHT30 and base version, SHT31 a standard version and All the way goes to SHT35 High end version which can be used in automotive level sensing.
SHT3x is packed with a completely new CMO Sens Chip, which will increase reliability along with improved accuracy in measuring. The SHT3x offers a range of new features when compared with SHT2x and other sensors, such as enhanced signal processing, two distinctive and user-selectable I2C addresses(0x44 or 0x45), an alert mode with programmable humidity and temperature limits, and communication speeds of up to 1 MHz.
Related Project: Digital Thermometer using LM35 and Arduino
SHT3x is more precise and accurate than other sensors like LM35, DHT11, DHT22, Thermistors, DS18B20 and has a greater range of measuring temperature than few of them which is -40° to +125°C (-40° to +257°F) and relative humidity ranging from 0 to 100%. It also has wide input voltage range from 2.2v to 5.5v.
It has an accuracy of ±3% to ±1.5% in measuring humidity from base version to high-end version respectively, And ±0.3 to ±0.1 in temperature measurements.
Specifications:
| Output | I²C, Voltage Out |
| Supply voltage range | 2.15 to 5.5 V |
| Energy consumption | 4.8µW (at 2.4 V, low repeatability, 1 measurement / s) |
| RH operating range | 0 – 100% RH |
| T operating range | -40 to +125°C (-40 to +257°F) |
| RH response time | 8 sec (tau63%) |
SHT3x Pinout diagram:
Below is the pinout diagram of SHT3X Temperature and Humidity Sensor.
From the above pinout diagram, There you can see 4 pins two pins for Voltage input and Ground and another two pins for I2C connection SCL and SDA.
Required Components:
- Sensirion SHT31 Humidity Temperature Sensor
- Arduino UNO R3 Development Board
- JHD162A 16×2 LCD Display
- Few connecting wires
Circuit Diagram:
Connect all the required components as shown in the above schematic diagram. Here we used LCD module with I2C adapter if you wish to connect it directly with out I2C refer the below link.
Connect Arduino with LCD Display with out I2C.
After connecting everything upload the code to Arduino, so it works accordingly.
Source Code:
Copy the below code and paste it in Arduino IDE, and select the correct board and serial port and click upload.
You need 2 libraries to run the below code you can directly install them through library manager or download them through below links manually.
| Brand | Arduino |
|---|
Related Products
The HW-201 IR infrared obstacle detection module can detect obstacles within a distance range of 2 cm to 30 cm, with a detection angle of 35 degrees.
It can operate with a supply voltage of 3.3 V to 5 V and has a maximum current consumption of 100 mA. The module outputs a digital signal, high when an obstacle is detected, low when no obstacle is detected.
The infrared LED has a wavelength of 940 nm and an operating frequency of 38 kHz. The module operates at temperatures between -25 °C and +55 °C.
The MQ2 analog gas sensor is used in gas leak detection equipment. This sensor is suitable for detecting LPG, butane, propane, methane, alcohol, hydrogen, and smoke. It has high sensitivity and a fast response time; the sensitivity can be adjusted using a potentiometer.
High-capacity brushless motor, maximizes equipment power and extends service life and reduces the risk of breakdowns. This motor is commonly used in industrial applications, comfortable and quite simple in its use, as well as its energy consumption is low.
MODULE compatible Arduino to control 4 motors DC or 2 stepper motors and have 2 connections for servomotors. This shield uses pins D3 to D12 for operation (direction, speed, etc).
The module is based on two L293D drivers and can control up to 4 DC motors with an intensity of 0.6 A per output (1.2 A at peak).
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button.
Transceiver module based on an NRF24L01 allowing a 2.4 GHz wireless connection. This module communicates with an Arduino or compatible microcontroller via the SPI bus.
The MQ3 analog gas sensor is suitable for detecting alcohol; this sensor can be used in a breathalyzer.
It has high sensitivity to alcohol and low sensitivity to gasoline.
The sensitivity can be adjusted using a potentiometer.
The SG90 servo motor is a type of continuous rotation motor controlled by a digital signal. It is used in projects such as robotics, position control systems, and DIY projects.
- ESP32-WROVER is a powerful, generic WiFi-BT-BLE MCU module that targets a wide variety of applications,ranging from low-power sensor networks to the most demanding tasks, such as voice encoding, music streamingand MP3 decoding. The ESP32-WROVER has two versions: The ESP32-WROVER IPEX Module uses an IPEX antenna while the ESP32-WROVER PCB module has a PCB antenna.
The Arduino UNO is the best board to get started with electronics and coding. If this is your first experience tinkering with the platform, the UNO is the most robust board you can start playing with. The UNO is the most used and documented board of the whole Arduino family.
The ESP32-CAM is an ESP-WROOM-32 development board from AI Thinker, paired with a 2MP OV2640 color camera. The ESP32-CAM module also features an SD card reader that can be used to record images when an event is detected (e.g., presence or motion detector).
Stepper motor 28BY J-48 with Driver ULN2003
the ULN2003 stepper motor driver or in English stepper motor, unipolar (4 phases/ 5 wires ) allows you to easily plug the small motor 28BY J-48 5v gràce to the 5 pin male connector and connects easily to an arduino or other through a 4 pin connector for control signals and Gnd (ground/-). The power supply of ULN2003 is between 5 and 12V.
