English
Français
IR Infrared Obstacle Detector Module
The HW-201 IR infrared obstacle detection module can detect obstacles within a distance range of 2 cm to 30 cm, with a detection angle of 35 degrees.
It can operate with a supply voltage of 3.3 V to 5 V and has a maximum current consumption of 100 mA. The module outputs a digital signal, high when an obstacle is detected, low when no obstacle is detected.
The infrared LED has a wavelength of 940 nm and an operating frequency of 38 kHz. The module operates at temperatures between -25 °C and +55 °C.
400,00 DA
IR Infrared Obstacle Detection Module
The IR infrared obstacle detection module is an essential electronic component for robotics projects, alarm systems, and security devices. It can detect the presence of nearby obstacles and provide increased security.
The module is easy to use and can be integrated into a wide variety of electronic projects to enhance obstacle detection capabilities.
Technical Specifications:
-Detection Distance: 2 cm to 30 cm (ideally between 10 cm and 20 cm)
-Detection Angle: 35 degrees
-Operating Voltage: 3.3V to 5V
-Current Consumption: 100mA max
-Signal Output: Digital signal, high level when an obstacle is detected, low level when no obstacle is detected.
-Response Time: 2.5 ms
-Infrared LED Wavelength: 940nm
-Operating Frequency: 38kHz
-Operating Temperature: -25°C to +55°C
-Dimensions: 32mm x 14mm x 18mm
-Weight: 3g
| Brand | Arduino |
|---|
Related Products
Seven-segment display (5611AH):
- The 7-segment displays consist of a series of LEDs placed to form numbers.
- A 7-segment display allows you to view the digits from 0 to 9.
- Typical voltage: 2.2v / Current per segment max: 30mA
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button.
The “LJ12A3-4-Z/BX” is an inductive proximity sensor that detects metal objects within a 4mm range. It operates on a DC 6-36V power supply and has an NPN (Normally Open) digital output, meaning it completes a circuit to the signal line when it detects metal. These sensors are used in industrial automation for non-contact switching, control, and detection
0.56 inch Red 4 Digit 7 Segment LED Display CC 12pin
12mm 12528 LDR is a type of photoresistor with a 12mm diameter and the model number GL12528, which changes its resistance based on the intensity of light it is exposed to. The resistance of the component is high in the dark and drops significantly as light increases, making it useful for detecting ambient light levels
5621BS Red LED Display 2 Digit 7 Segment Common Anode Digital Display 18 Pin 0.56 inch
MODULE compatible Arduino to control 4 motors DC or 2 stepper motors and have 2 connections for servomotors. This shield uses pins D3 to D12 for operation (direction, speed, etc).
The module is based on two L293D drivers and can control up to 4 DC motors with an intensity of 0.6 A per output (1.2 A at peak).
3S 20A Li-ion 18650 BMS Lithium Battery Protection Board is a Battery Management System (BMS) designed for 3-cell 18650 Li-ion battery packs. It offers overcharge, over-discharge, short-circuit, and overcurrent protection to ensure the safe operation and longevity of your battery packs.
This is a general OLED display Module, 0.91inch diagonal, 128×32 pixels, with embedded controller, communicating via I2C interface.
