Français
English
Shield L293D Motor Controller
MODULE compatible Arduino to control 4 motors DC or 2 stepper motors and have 2 connections for servomotors. This shield uses pins D3 to D12 for operation (direction, speed, etc).
The module is based on two L293D drivers and can control up to 4 DC motors with an intensity of 0.6 A per output (1.2 A at peak).
1.100,00 DA
Adafruit Compatible Motor Control Shield (L293D Motor Driver)
L293D is an integrated, high voltage, monolithic high current, 4 channel driver. Basically that means by using this chip you can use DC motors and power supplies of up to 36 Volts, thats some very big motors and the chip can provide a maximum current 600mA per channel, the L293D chip is also what is known as a type of H-Bridge. The H-bridge is typically an electrical circuit that allows a voltage to be applied through a load in both directions to an output, for example, motor.
– 2 interface for 5V servo connected to high resolution dedicated timer – no jitter!
– Can drive 4 DC motors or 2 stepper motors or 2 Servo
– Up to 4 bidirectional DC motors with individual 8-bit speed selection
– Up to 2 stepper motors (unipolar or bipolar) with single coil, double winding or interlocking stepping.
-4 H-Bridges: per bridge provides (current 1.2A peak) of 0.6A with thermal protection, motors can operate on 4.5V to 36V DC
– Unroll resistors keep motors disabled during power on
– reset button
– 2 external terminal power interface, for logic separators/ automotive supplies
– Tested compatible for Mega, Diecimila and Duemilanove
Produits connexes
5mm 5537 LDR is a 5mm light-dependent resistor with a « 5537 » model number, which is a photosensitive component that changes its electrical resistance based on the intensity of ambient light. Its resistance is high in darkness and decreases as light increases, making it useful for light-sensitive applications like automatic lighting systems, alarms, and light-level detection.
The HW-201 IR infrared obstacle detection module can detect obstacles within a distance range of 2 cm to 30 cm, with a detection angle of 35 degrees.
It can operate with a supply voltage of 3.3 V to 5 V and has a maximum current consumption of 100 mA. The module outputs a digital signal, high when an obstacle is detected, low when no obstacle is detected.
The infrared LED has a wavelength of 940 nm and an operating frequency of 38 kHz. The module operates at temperatures between -25 °C and +55 °C.
0.56 inch Red 4 Digit 7 Segment LED Display CC 12pin
- ESP32-WROVER is a powerful, generic WiFi-BT-BLE MCU module that targets a wide variety of applications,ranging from low-power sensor networks to the most demanding tasks, such as voice encoding, music streamingand MP3 decoding. The ESP32-WROVER has two versions: The ESP32-WROVER IPEX Module uses an IPEX antenna while the ESP32-WROVER PCB module has a PCB antenna.
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button.
5621BS Red LED Display 2 Digit 7 Segment Common Anode Digital Display 18 Pin 0.56 inch
0.56 inch 4 Digit 7 Segment LED Display Red Clock 12 Pin Common Cathode Digital Display
The MQ2 analog gas sensor is used in gas leak detection equipment. This sensor is suitable for detecting LPG, butane, propane, methane, alcohol, hydrogen, and smoke. It has high sensitivity and a fast response time; the sensitivity can be adjusted using a potentiometer.
1.3-inch OLED display module with a 128×64 pixel resolution and a blue monochrome screen. It uses an I2C/IIC interface for communication, requires a 4-pin connection, and is compatible with 3.3V to 5V microcontrollers like the Arduino. Key features include high brightness, self-emission (no backlight needed), high contrast, low power consumption, and a wide viewing angle
