Français
English
Arduino Starter Kit
The Arduino Starter Kit is a comprehensive, beginner-friendly bundle designed to teach the fundamentals of electronics, coding, and prototyping through hands-on projects. It typically includes an Arduino Uno board, jumper wires, a breadboard, and various sensors/actuators (LEDs, motors, sensors…)….
9.200,00 DA
The ARDUINO Starter kit contains:
- x 1 Arduino UNO R3 board (compatible)
- x 1 Breadboard 830 points
- x 1 LCD Module 1602
- x 1 Keyboard 4*4
- x 1 Display 7 Segment 1 Digit
- x 1 Display 7 Segment 4 Digit
- x 1 Dot matrix 8*8
- x 1 74HC595N
- x 1 Temperature sensor LM35
- x 2 DS18B20 Buzzer
- x 1 Servo SG-90
- x 1 Stepper motor 5V
- x 1 ULN2003 driver card
- x 1 DS1302 Clock Module
- x 1 Joystick Module
- x 1 Channel Relay module
- x 1 pack wire connector M-M 65 pcs
- x 1 Temperature and humidity sensor module DHT11
- x 1 fich stack 9v with door
- x 1 Càble USB
- x 1 Infrared remote control with receiver
- x 1 Sound detection sensor
- x 1 Potentiometer 10K
- 1 x 5mm flame sensor
- 1 x LDR 5mm
- x 10 LED 5mm red
- x 10 5mm yellow LED
- x 10 LED 5mm green
- 10 x 220R resistance 1/4W
- 10 x 1k resistance 1/4W
- 10 x 10K resistance 1/4W
- x 5 Push button 12×12 mm
- x 2 ball switch
Produits connexes
0.56 inch Red 4 Digit 7 Segment LED Display CC 12pin
- ESP32-WROVER is a powerful, generic WiFi-BT-BLE MCU module that targets a wide variety of applications,ranging from low-power sensor networks to the most demanding tasks, such as voice encoding, music streamingand MP3 decoding. The ESP32-WROVER has two versions: The ESP32-WROVER IPEX Module uses an IPEX antenna while the ESP32-WROVER PCB module has a PCB antenna.
The « LJ12A3-4-Z/BX » is an inductive proximity sensor that detects metal objects within a 4mm range. It operates on a DC 6-36V power supply and has an NPN (Normally Open) digital output, meaning it completes a circuit to the signal line when it detects metal. These sensors are used in industrial automation for non-contact switching, control, and detection
Transceiver module based on an NRF24L01 allowing a 2.4 GHz wireless connection. This module communicates with an Arduino or compatible microcontroller via the SPI bus.
MODULE compatible Arduino to control 4 motors DC or 2 stepper motors and have 2 connections for servomotors. This shield uses pins D3 to D12 for operation (direction, speed, etc).
The module is based on two L293D drivers and can control up to 4 DC motors with an intensity of 0.6 A per output (1.2 A at peak).
The SG90 servo motor is a type of continuous rotation motor controlled by a digital signal. It is used in projects such as robotics, position control systems, and DIY projects.
5621BS Red LED Display 2 Digit 7 Segment Common Anode Digital Display 18 Pin 0.56 inch
The MQ2 analog gas sensor is used in gas leak detection equipment. This sensor is suitable for detecting LPG, butane, propane, methane, alcohol, hydrogen, and smoke. It has high sensitivity and a fast response time; the sensitivity can be adjusted using a potentiometer.
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button.
