Français
English
Arduino Mega 2560 R3 With Cable
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button.
4.200,00 DA
Universal Atmega2560 microcontroller module for use in prototypes and projects with microcontrollers. Compatible with the Arduino® Mega 2560 design.
It is a clone that was built according to the original scheme.
The programming is done using the USB UART CH340 converter.
You will need a USB A / B cable to communicate with the board .
Parameters:
- Supply voltage: 5V (USB), 7-12V (power adapter)
- I / O pin voltage: 5V
- Arduino® Mega 2560 R3 bootloader installed
- USB-UART chip: CH340
- Microcontroller: ATmega2560
- Maximum clock frequency: 16 MHz
- SRAM memory: 8 kB
- Flash memory: 256 KB (8 KB is reserved for bootloader)
- EEPROM memory: 4 kB
- I / O Ports: 54
- PWM outputs: 15
- Number of analog inputs: 16 (channels of A / C converter)
- Serial interfaces: UART, SPI, I2C
- External interrupts
- Dimensions: 101 x 54 x 15 mm
- Goldpins soldered into the board
| Poids | 1 kg |
|---|---|
| Marque | Arduino |
Produits connexes
This is 125K RFID Tag. The RFID technology is used for sensing and identifying tagged people and objects for access control, automation, and a whole range of different applications.
Operating on a frequency of 125kHz, these tokens are all pre-programmed with unique ID numbers to communicate wirelessly with RFID Readers over distances of around 10cm or less. This means you can attach it to vehicles or items, keyrings or even pets’ collars to keep track of the location via an array of readers in the office, warehouse or home.
Transceiver module based on an NRF24L01 allowing a 2.4 GHz wireless connection. This module communicates with an Arduino or compatible microcontroller via the SPI bus.
The SG90 servo motor is a type of continuous rotation motor controlled by a digital signal. It is used in projects such as robotics, position control systems, and DIY projects.
Arduino Nano has enough processing power to control many electronic components. It has several I/O pins, which allows to connect it to many components. , it is a compact and reduced version of Arduino uno maroc.
Arduino Nano has 14 digital inputs/types (6 of which can be used as PWM outputs), 8 analog inputs.
4 Digit 0.56 inch 7 Segment 4 Bit Red LED Digital Display Module Tube with Clock Point for Arduino
The « LJ12A3-4-Z/BX » is an inductive proximity sensor that detects metal objects within a 4mm range. It operates on a DC 6-36V power supply and has an NPN (Normally Open) digital output, meaning it completes a circuit to the signal line when it detects metal. These sensors are used in industrial automation for non-contact switching, control, and detection
0.56 inch Red 4 Digit 7 Segment LED Display CC 12pin
0.56 inch 4 Digit 7 Segment LED Display Red Clock 12 Pin Common Cathode Digital Display
The MQ3 analog gas sensor is suitable for detecting alcohol; this sensor can be used in a breathalyzer.
It has high sensitivity to alcohol and low sensitivity to gasoline.
The sensitivity can be adjusted using a potentiometer.
MODULE compatible Arduino to control 4 motors DC or 2 stepper motors and have 2 connections for servomotors. This shield uses pins D3 to D12 for operation (direction, speed, etc).
The module is based on two L293D drivers and can control up to 4 DC motors with an intensity of 0.6 A per output (1.2 A at peak).
The Arduino UNO is the best board to get started with electronics and coding. If this is your first experience tinkering with the platform, the UNO is the most robust board you can start playing with. The UNO is the most used and documented board of the whole Arduino family.
