Français
English
0.56 inch 4 Digit 7 Segment LED Display CA Red
4 Digit 0.56 inch 7 Segment 4 Bit Red LED Digital Display Module Tube with Clock Point for Arduino
Description
- The module is based on a 4 (0.56 inch) digital tube which can display the clock point. The decimal point is not displayed and the driver chip is TM1637.
- Simply two signal lines can do 4 digit 7 segment LED MCU control. It can be used to display the integer, clock, stopwatch, score, etc.
Features
1.Compatible for Arduino UNO R3/MEGA2560/Leonardo.
2.4-digit alpha-numeric red display with clock dot.
3. 8 gray adjustable.
4. Power supply should be 3.3~5.5V DC.
5. Interface logic level can be 3.3V/5V.
6. 4 screw mounting holes which diameter is 2.2mm.
Produits connexes
The Arduino UNO is the best board to get started with electronics and coding. If this is your first experience tinkering with the platform, the UNO is the most robust board you can start playing with. The UNO is the most used and documented board of the whole Arduino family.
Seven-segment display (5611AH):
- The 7-segment displays consist of a series of LEDs placed to form numbers.
- A 7-segment display allows you to view the digits from 0 to 9.
- Typical voltage: 2.2v / Current per segment max: 30mA
0.56 inch Red 4 Digit 7 Segment LED Display CC 12pin
- ESP32-WROVER is a powerful, generic WiFi-BT-BLE MCU module that targets a wide variety of applications,ranging from low-power sensor networks to the most demanding tasks, such as voice encoding, music streamingand MP3 decoding. The ESP32-WROVER has two versions: The ESP32-WROVER IPEX Module uses an IPEX antenna while the ESP32-WROVER PCB module has a PCB antenna.
5mm 5537 LDR is a 5mm light-dependent resistor with a « 5537 » model number, which is a photosensitive component that changes its electrical resistance based on the intensity of ambient light. Its resistance is high in darkness and decreases as light increases, making it useful for light-sensitive applications like automatic lighting systems, alarms, and light-level detection.
- Wheelbase: 330mm
- Material: Glass Fiber + Polyamide-Nylon
- Moter Mounting Hole Diameter: 3 mm
- Arm Size: 155×34 (LxW) mm
- Weight: 160 gm
- Magnification: Up to 1000X for fine details.
- LCD Screen: Large 4.3-inch screen for clear viewing.
- Resolution: 10MP for sharp, detailed images.
- LED Light: Built-in light for better visibility.
- Versatile: Ideal for observing various samples.
The MQ2 analog gas sensor is used in gas leak detection equipment. This sensor is suitable for detecting LPG, butane, propane, methane, alcohol, hydrogen, and smoke. It has high sensitivity and a fast response time; the sensitivity can be adjusted using a potentiometer.
The SHT3x sensor is the most accurate and precise sensor for measuring humidity and temperature parameters compared to other temperature sensors like LM35, Thermistor, DS18B20 & DHT11/DHT22. Thus SHT3x can be used for industrial applications because of the high accuracy and good sensitivity. Its Relative Humidity operating range is 0 – 100% and Temperature operating range is -40° to +125°C (-40° to +257°F).
5621BS Red LED Display 2 Digit 7 Segment Common Anode Digital Display 18 Pin 0.56 inch
The HW-201 IR infrared obstacle detection module can detect obstacles within a distance range of 2 cm to 30 cm, with a detection angle of 35 degrees.
It can operate with a supply voltage of 3.3 V to 5 V and has a maximum current consumption of 100 mA. The module outputs a digital signal, high when an obstacle is detected, low when no obstacle is detected.
The infrared LED has a wavelength of 940 nm and an operating frequency of 38 kHz. The module operates at temperatures between -25 °C and +55 °C.
Transceiver module based on an NRF24L01 allowing a 2.4 GHz wireless connection. This module communicates with an Arduino or compatible microcontroller via the SPI bus.
