Français
English
Arduino Starter Kit
The Arduino Starter Kit is a comprehensive, beginner-friendly bundle designed to teach the fundamentals of electronics, coding, and prototyping through hands-on projects. It typically includes an Arduino Uno board, jumper wires, a breadboard, and various sensors/actuators (LEDs, motors, sensors…)….
9.200,00 DA
The ARDUINO Starter kit contains:
- x 1 Arduino UNO R3 board (compatible)
- x 1 Breadboard 830 points
- x 1 LCD Module 1602
- x 1 Keyboard 4*4
- x 1 Display 7 Segment 1 Digit
- x 1 Display 7 Segment 4 Digit
- x 1 Dot matrix 8*8
- x 1 74HC595N
- x 1 Temperature sensor LM35
- x 2 DS18B20 Buzzer
- x 1 Servo SG-90
- x 1 Stepper motor 5V
- x 1 ULN2003 driver card
- x 1 DS1302 Clock Module
- x 1 Joystick Module
- x 1 Channel Relay module
- x 1 pack wire connector M-M 65 pcs
- x 1 Temperature and humidity sensor module DHT11
- x 1 fich stack 9v with door
- x 1 Càble USB
- x 1 Infrared remote control with receiver
- x 1 Sound detection sensor
- x 1 Potentiometer 10K
- 1 x 5mm flame sensor
- 1 x LDR 5mm
- x 10 LED 5mm red
- x 10 5mm yellow LED
- x 10 LED 5mm green
- 10 x 220R resistance 1/4W
- 10 x 1k resistance 1/4W
- 10 x 10K resistance 1/4W
- x 5 Push button 12×12 mm
- x 2 ball switch
Produits connexes
The « LJ12A3-4-Z/BX » is an inductive proximity sensor that detects metal objects within a 4mm range. It operates on a DC 6-36V power supply and has an NPN (Normally Open) digital output, meaning it completes a circuit to the signal line when it detects metal. These sensors are used in industrial automation for non-contact switching, control, and detection
The SHT3x sensor is the most accurate and precise sensor for measuring humidity and temperature parameters compared to other temperature sensors like LM35, Thermistor, DS18B20 & DHT11/DHT22. Thus SHT3x can be used for industrial applications because of the high accuracy and good sensitivity. Its Relative Humidity operating range is 0 – 100% and Temperature operating range is -40° to +125°C (-40° to +257°F).
The Arduino UNO is the best board to get started with electronics and coding. If this is your first experience tinkering with the platform, the UNO is the most robust board you can start playing with. The UNO is the most used and documented board of the whole Arduino family.
3S 20A Li-ion 18650 BMS Lithium Battery Protection Board is a Battery Management System (BMS) designed for 3-cell 18650 Li-ion battery packs. It offers overcharge, over-discharge, short-circuit, and overcurrent protection to ensure the safe operation and longevity of your battery packs.
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button.
5mm 5537 LDR is a 5mm light-dependent resistor with a « 5537 » model number, which is a photosensitive component that changes its electrical resistance based on the intensity of ambient light. Its resistance is high in darkness and decreases as light increases, making it useful for light-sensitive applications like automatic lighting systems, alarms, and light-level detection.
- ESP32-WROVER is a powerful, generic WiFi-BT-BLE MCU module that targets a wide variety of applications,ranging from low-power sensor networks to the most demanding tasks, such as voice encoding, music streamingand MP3 decoding. The ESP32-WROVER has two versions: The ESP32-WROVER IPEX Module uses an IPEX antenna while the ESP32-WROVER PCB module has a PCB antenna.
Transceiver module based on an NRF24L01 allowing a 2.4 GHz wireless connection. This module communicates with an Arduino or compatible microcontroller via the SPI bus.
Stepper motor 28BY J-48 with Driver ULN2003
the ULN2003 stepper motor driver or in English stepper motor, unipolar (4 phases/ 5 wires ) allows you to easily plug the small motor 28BY J-48 5v gràce to the 5 pin male connector and connects easily to an arduino or other through a 4 pin connector for control signals and Gnd (ground/-). The power supply of ULN2003 is between 5 and 12V.
This is 125K RFID Tag. The RFID technology is used for sensing and identifying tagged people and objects for access control, automation, and a whole range of different applications.
Operating on a frequency of 125kHz, these tokens are all pre-programmed with unique ID numbers to communicate wirelessly with RFID Readers over distances of around 10cm or less. This means you can attach it to vehicles or items, keyrings or even pets’ collars to keep track of the location via an array of readers in the office, warehouse or home.
