Français
English
Arduino Starter Kit
The Arduino Starter Kit is a comprehensive, beginner-friendly bundle designed to teach the fundamentals of electronics, coding, and prototyping through hands-on projects. It typically includes an Arduino Uno board, jumper wires, a breadboard, and various sensors/actuators (LEDs, motors, sensors…)….
9.200,00 DA
The ARDUINO Starter kit contains:
- x 1 Arduino UNO R3 board (compatible)
- x 1 Breadboard 830 points
- x 1 LCD Module 1602
- x 1 Keyboard 4*4
- x 1 Display 7 Segment 1 Digit
- x 1 Display 7 Segment 4 Digit
- x 1 Dot matrix 8*8
- x 1 74HC595N
- x 1 Temperature sensor LM35
- x 2 DS18B20 Buzzer
- x 1 Servo SG-90
- x 1 Stepper motor 5V
- x 1 ULN2003 driver card
- x 1 DS1302 Clock Module
- x 1 Joystick Module
- x 1 Channel Relay module
- x 1 pack wire connector M-M 65 pcs
- x 1 Temperature and humidity sensor module DHT11
- x 1 fich stack 9v with door
- x 1 Càble USB
- x 1 Infrared remote control with receiver
- x 1 Sound detection sensor
- x 1 Potentiometer 10K
- 1 x 5mm flame sensor
- 1 x LDR 5mm
- x 10 LED 5mm red
- x 10 5mm yellow LED
- x 10 LED 5mm green
- 10 x 220R resistance 1/4W
- 10 x 1k resistance 1/4W
- 10 x 10K resistance 1/4W
- x 5 Push button 12×12 mm
- x 2 ball switch
Produits connexes
MODULE compatible Arduino to control 4 motors DC or 2 stepper motors and have 2 connections for servomotors. This shield uses pins D3 to D12 for operation (direction, speed, etc).
The module is based on two L293D drivers and can control up to 4 DC motors with an intensity of 0.6 A per output (1.2 A at peak).
The SG90 servo motor is a type of continuous rotation motor controlled by a digital signal. It is used in projects such as robotics, position control systems, and DIY projects.
12mm 12528 LDR is a type of photoresistor with a 12mm diameter and the model number GL12528, which changes its resistance based on the intensity of light it is exposed to. The resistance of the component is high in the dark and drops significantly as light increases, making it useful for detecting ambient light levels
0.56 inch Red 4 Digit 7 Segment LED Display CC 12pin
The SHT3x sensor is the most accurate and precise sensor for measuring humidity and temperature parameters compared to other temperature sensors like LM35, Thermistor, DS18B20 & DHT11/DHT22. Thus SHT3x can be used for industrial applications because of the high accuracy and good sensitivity. Its Relative Humidity operating range is 0 – 100% and Temperature operating range is -40° to +125°C (-40° to +257°F).
3S 20A Li-ion 18650 BMS Lithium Battery Protection Board is a Battery Management System (BMS) designed for 3-cell 18650 Li-ion battery packs. It offers overcharge, over-discharge, short-circuit, and overcurrent protection to ensure the safe operation and longevity of your battery packs.
5mm 5537 LDR is a 5mm light-dependent resistor with a « 5537 » model number, which is a photosensitive component that changes its electrical resistance based on the intensity of ambient light. Its resistance is high in darkness and decreases as light increases, making it useful for light-sensitive applications like automatic lighting systems, alarms, and light-level detection.
The HW-201 IR infrared obstacle detection module can detect obstacles within a distance range of 2 cm to 30 cm, with a detection angle of 35 degrees.
It can operate with a supply voltage of 3.3 V to 5 V and has a maximum current consumption of 100 mA. The module outputs a digital signal, high when an obstacle is detected, low when no obstacle is detected.
The infrared LED has a wavelength of 940 nm and an operating frequency of 38 kHz. The module operates at temperatures between -25 °C and +55 °C.
