Français
English
Arduino Starter Kit
The Arduino Starter Kit is a comprehensive, beginner-friendly bundle designed to teach the fundamentals of electronics, coding, and prototyping through hands-on projects. It typically includes an Arduino Uno board, jumper wires, a breadboard, and various sensors/actuators (LEDs, motors, sensors…)….
9.200,00 DA
The ARDUINO Starter kit contains:
- x 1 Arduino UNO R3 board (compatible)
- x 1 Breadboard 830 points
- x 1 LCD Module 1602
- x 1 Keyboard 4*4
- x 1 Display 7 Segment 1 Digit
- x 1 Display 7 Segment 4 Digit
- x 1 Dot matrix 8*8
- x 1 74HC595N
- x 1 Temperature sensor LM35
- x 2 DS18B20 Buzzer
- x 1 Servo SG-90
- x 1 Stepper motor 5V
- x 1 ULN2003 driver card
- x 1 DS1302 Clock Module
- x 1 Joystick Module
- x 1 Channel Relay module
- x 1 pack wire connector M-M 65 pcs
- x 1 Temperature and humidity sensor module DHT11
- x 1 fich stack 9v with door
- x 1 Càble USB
- x 1 Infrared remote control with receiver
- x 1 Sound detection sensor
- x 1 Potentiometer 10K
- 1 x 5mm flame sensor
- 1 x LDR 5mm
- x 10 LED 5mm red
- x 10 5mm yellow LED
- x 10 LED 5mm green
- 10 x 220R resistance 1/4W
- 10 x 1k resistance 1/4W
- 10 x 10K resistance 1/4W
- x 5 Push button 12×12 mm
- x 2 ball switch
Produits connexes
The HW-201 IR infrared obstacle detection module can detect obstacles within a distance range of 2 cm to 30 cm, with a detection angle of 35 degrees.
It can operate with a supply voltage of 3.3 V to 5 V and has a maximum current consumption of 100 mA. The module outputs a digital signal, high when an obstacle is detected, low when no obstacle is detected.
The infrared LED has a wavelength of 940 nm and an operating frequency of 38 kHz. The module operates at temperatures between -25 °C and +55 °C.
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button.
- Magnification: Up to 1000X for fine details.
- LCD Screen: Large 4.3-inch screen for clear viewing.
- Resolution: 10MP for sharp, detailed images.
- LED Light: Built-in light for better visibility.
- Versatile: Ideal for observing various samples.
The Arduino UNO is the best board to get started with electronics and coding. If this is your first experience tinkering with the platform, the UNO is the most robust board you can start playing with. The UNO is the most used and documented board of the whole Arduino family.
Stepper motor 28BY J-48 with Driver ULN2003
the ULN2003 stepper motor driver or in English stepper motor, unipolar (4 phases/ 5 wires ) allows you to easily plug the small motor 28BY J-48 5v gràce to the 5 pin male connector and connects easily to an arduino or other through a 4 pin connector for control signals and Gnd (ground/-). The power supply of ULN2003 is between 5 and 12V.
- ESP32-WROVER is a powerful, generic WiFi-BT-BLE MCU module that targets a wide variety of applications,ranging from low-power sensor networks to the most demanding tasks, such as voice encoding, music streamingand MP3 decoding. The ESP32-WROVER has two versions: The ESP32-WROVER IPEX Module uses an IPEX antenna while the ESP32-WROVER PCB module has a PCB antenna.
0.56 inch 4 Digit 7 Segment LED Display Red Clock 12 Pin Common Cathode Digital Display
Arduino Nano has enough processing power to control many electronic components. It has several I/O pins, which allows to connect it to many components. , it is a compact and reduced version of Arduino uno maroc.
Arduino Nano has 14 digital inputs/types (6 of which can be used as PWM outputs), 8 analog inputs.
A 5v relay is an automatic switch that is commonly used in an automatic control circuit and to control a high-current using a low-current signal. The input voltage of the relay signal ranges from 0 to 5V.
The « LJ12A3-4-Z/BX » is an inductive proximity sensor that detects metal objects within a 4mm range. It operates on a DC 6-36V power supply and has an NPN (Normally Open) digital output, meaning it completes a circuit to the signal line when it detects metal. These sensors are used in industrial automation for non-contact switching, control, and detection
